Categories :

Can you over grease u-joints?

Can you over grease u-joints?

There is no such thing as greasing a u-joint too much. If you don’t like the grease getting all over the frame, make yourself a splatter shield out of sheet metal.

How long do driveshaft u-joints last?

U-joints can last decades, or they can break when the vehicle is still new. That’s why it’s a good idea to check the u-joints at every oil change. A typical rear wheel drive vehicle has 2 or 3 u-joints. Some vehicles with a long wheel base, such as buses, have 3 or more u-joints.

How do I know if my driveshaft u-joints are bad?

A bad u-joint can cause a clunking sound or jerkiness while driving, particularly when letting off of and pressing the accelerator. A bad u-joint can also cause vibration at certain speeds, emanating from the center or rear of the vehicle.

What is a 1310 u-joint?

1310 U-Joint Series is the most common U-Joint ever used. It is still used on OE applications. 1.062 cap and 3.219 width. ( 1 1/16 x 3 1/4 close) 1330 U-Joint Series is very common and used on OE production.

What is the recommended lubricant for a universal joint?

The recommended grease for u-joints is NLGI #2 GC-LB lithium complex EP grease, preferably a synthetic. Use care not to lose a needle bearing when removing and reinstalling the caps.

How do you know when to replace U joints?

Symptoms of a Bad or Failing Universal Joint (U-Joint)

  1. Squeaking noise when starting to move (forward or reverse)
  2. “Clunk” with a ringing sound when shifting from Drive to Reverse.
  3. Vibration felt throughout the vehicle while moving forward at speed.
  4. Transmission fluid leaks from the rear of the transmission.

How much does it cost to replace U joints?

U-Joint Replacement Cost – RepairPal Estimate. Labor costs are estimated between $106 and $134 while parts are priced between $130 and $150. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location. Related repairs may also be needed.

What does a bad driveshaft sound like?

Generally speaking, a bad drive shaft is going to create a kind of rattling or clunking sound. You may also hear sounds that are like a high-pitched squeaking or a scraping noise of metal on metal. All of this will originate from underneath your car, rather than in the engine compartment.

How much does it cost to replace a u-joint?

The average price for the u joint replacement cost ranges between $190 and $260 for the replacement, while the labor on this job runs between $170 and $210 on aveage, with the parts ranging between $20 and $50. Keep in mind, the average u joint replacement cost will vary depending on the type of vehicle you have.

What is the difference between 1310 and 1350 U joint?

Size and strength. The 1310 series joint is what you would expect to find stock in most Jeep or small trucks. A 1350 series joint/shaft is what you might find in many full size trucks. While it’s not 100% accurate, you could say that a 1310 is a “half ton” joint and a 1350 is a “one ton joint”.

What is the difference between 1330 and 1350 U joint?

The 1310 series u-joint measures approximately 3 1/4 inches wide. The 1330 and 1350 both measure approximately 3 5/8 wide. The 1350 series has a cap diameter of 1 3/16 inch and the body and journals are bigger than the 1310 or 1330.

How are universal joint parts identified by series?

All Universal Joint parts are identified by the series of the Joint. In order to determine the joint series, some investigation is required. The Type of Cap varies by manufacturer of the component, and often we find that customers are seeking universal joint that are a combination of sizes. The cap type abreviations we use are:

What are the abreviations of the you joint cap?

The cap type abreviations we use are: OSR = Outside Snap Ring – a clip that is on the TOP of the universal joint cap when installed ISR = Inside Snap Ring – These are known as “C” clips and are installed between the ears of the yoke into a groove in the U-Joint cap.

What are the different types of universal joints?

The Type of Cap varies by manufacturer of the component, and often we find that customers are seeking universal joint that are a combination of sizes. The cap type abreviations we use are: ISR = Inside Snap Ring – These are known as “C” clips and are installed between the ears of the yoke into a groove in the U-Joint cap.