Categories :

How do I adjust the smoke on my water amp?

How do I adjust the smoke on my water amp?

Amp settings

  1. Drive – 7.
  2. Treble – 3.
  3. Mid – 7.
  4. Bass – 9.
  5. Reverb – 3.

What setting should my amp be on?

The treble is best kept on around 6 or lower, or it can become a bit too sharp. You may want to increase the treble a bit more if you’re using high gain, to try and give your tone a bit more clarity. Having the bass on around 5 is a good place to start because it makes your tone thick but without being too muffled.

What is the tempo of smoke on water?

Smoke on the Water is avery happysong byDeep Purplewith a tempo of114 BPM.It can also be used half-time at57 BPM or double-time at228 BPM.

What should I set my HPF and LPF to?

You usually set the HPF with a steep slope say 24db/octave because you are trying to protect the sub from damage and a 12-18db/octave on the LPF because you want it to kinda “blend” in with your mids. The steeper the slope (db/octave) the less your sub will creep into the neighboring frequencies.

What does tone setting on AMP do?

EQ or Tone Using these controls have a similar effect to adjusting the treble and bass. If you turn the control up, then you’ll put more emphasis on the treble, making your guitar sound sharper. If you turn the tone/ EQ control down, then your tone will become more mellow.

What is the sixth string on a guitar?

The thickest string is called the 6th string. In standard guitar tuning, this is tuned to E and is often referred to as the “low E string,” meaning the lowest note you can play.

How do I make my amp sound crunchy?

The first way to achieve a crunch tone is by pushing the amp with pedals. A boost pedal does just what the name implies. It boosts the signal coming from the guitar. When your amplifier gets this super hot signal from your guitar it starts to clip.

What does Eq do on an amp?

The EQ knobs on your amp control your overall balance of tone. EQ is a way for you to shape your tone in a very controlled manner. It gives you a way to dial in Normally guitar amps have three EQ knobs: Low/Bass, Mid, High/Treble. Some amps even have a fourth EQ knob to give you more control: presence.

What key is smoke on the water played in?

Smoke On The Water is in the key of G minor (relative major is B-flat major).

What are the amp settings for a Marshall 1922?

JMP-1 into Digitech Studio Quad V2 All mono. Then use one side of a Marshall 9100 power amp,Voicing B, into a Marshall 1922……. 2 x 12 cab. For Lead I use the same settings as above, but up the gain to 19 and push the treble up a couple of notches.I also add some delay.

Are there different amp settings for Marshall guitar?

Discussion in ‘ Marshall Amps ‘ started by fiftycalibre, Oct 22, 2007 . Here are two different amp settings you might like to try. I think these are pretty close. Guitar is straight into amp with no FX. OD channel. Does anyone have settings they want to share? Good thread.

What kind of Valve did a Marshall 1959 have?

If you look at archive footage of classic rock legends like Jimmy Page, Jimi Hendrix and Paul Kossoff, you’ll often see a Marshall 1959 with the jumper lead. 2. The rear panel valves Early Marshalls were based on classic tweed Fenders and used the KT66 valve, which was a British version of the American 6L6.

What kind of sound did Marshall amplifiers make?

While earlier Marshalls owed more than a little to the 1950s Fender Bassman, the 1959 is generally regarded as the genesis of the true Marshall sound. It was the first Marshall to feature EL34s and the first amplifier head to sit on top of a 4×12 cabinet.