How do I program my 6160RF keypad?

First, you need to address your 6160RF to your panel. Enter programming by pressing 1 and 3 simultaneously on the keypad within 60 seconds of powering up. The keypad should display CON ADDRESS = 31 as 31 is the default keypad address. You will need to change that address to the correct address for your alarm system.

Is Honeywell 6160 a wireless network?

Honeywell 6160 is an alphanumeric keypad with no built-in wireless receiver. So, it means if you want to connect wireless devices with the control panel that is equipped with 6160, you will need to install a wireless receiver product. It is an unlimited zone wireless receiver.

How many zones does a 6160RF have?

The Honeywell 6160RF has a 2 line alpha numeric keypad display which allows users to access the *56 zone programming mode.

How do you program a Honeywell wireless sensor?

Complete the following steps to program a wireless zone on a Honeywell VISTA-20P:

Access system programming. Enter the installer code (the default code is 4112) + 800 on a keypad.
Access zone programming. Enter * 56.
Select a zone.
Program the zone.
Exit programming.
Test the sensor.

How do I connect my Honeywell wireless sensor?

Wireless Indoor Sensor Install batteries and link sensor to thermostat Install batteries, then enter Wireless Setup mode at the thermostat. Press and release the CONNECT button to link the wireless sensor to the thermostat. Press and release CONNECT. After a short delay, the status light will glow green for 15 seconds.

How do you clear the code on a Honeywell alarm?

Clear the keypad error by entering your four-digit security code and then pressing 1 (OFF key). If the screen shows a BAT error, which indicates a low system battery, this should clear when the battery recharges after 48 hours at the most.

How do you wire a Honeywell 6160 keypad?

Run the black wire from the (-) terminal on the keypad to the Aux Pwr (GND) terminal on the control panel. Run the red wire from the (++) terminal on the keypad to the Aux Pwr terminal on the control panel. Run the yellow wire from the Y terminal on the keypad to the “data out” terminal on the control panel.

How do I change the code on my Honeywell keypad?

How to change the master code of a Honeywell Alarm system

Press 8 (the CODE key).
Press 02.
Enter a new four-digit master code.
Re-enter the new code. The keypad will beep once to let you know that the code has been changed.

How do I reset my alarm keypad?

Locate the keypad and pull down the panel that covers the keypad on your alarm system. Then, enter your 4 digit master code, wait 2 seconds, and then enter it again. On some models, this step will reset the alarm and stop it from ringing.

How many wireless zones does Vista 15P have?

The Honeywell Vista 15P has 6 on board hardwired zones, 16 hardwired expansion zones (totaling 22 hardwired zones), and up to 26 wireless expansion zones. The Vista 15p also supports 8 independent keyfob zones allowing programming without using any of the 26 wireless expansion zones.

What is the Ademco 6160rf keypad / transceiver used for?

The ADEMCO 6160RF keypad/transceiver is a combination unit that combines the functions of the following devices: 6160 Alphanumeric Addressable Keypad 5881H RF Receiver 5800TM Transmitter Module The 6160RF Keypad/Transceiver may be used on any control panel that supports 5800 Series wireless devices (e.g., VISTA-10P, VISTA-15P, VISTA-20P).

Are there any 6160rf keypads left in stock?

Only 2 left in stock – order soon. . Only 15 left in stock – order soon. . Only 5 left in stock – order soon. . Only 9 left in stock – order soon.

Are there any wireless keypads for Vista Pro?

Dealers can add the 5828 and 5828V wireless keypads to VISTA for the first time, presenting a tremendous upsell opportunity by letting them offer their customers secondary wireless keypads on every installation with virtually no install time.