What does it mean when your vape says check atomizer?

If you press the firing button on your e-cig and you see the message ‘no atomizer’ or ‘check atomizer’ it means that your vape mod is not reading the coil within your vape tank properly. If your vape mod can’t detect your atomizer head, then it cannot properly deliver power to it.

How do I fix check atomizer Smok?

Recap

Clean all contacts on battery/mod, tank or pod.
Remove and reinstall the coil (after cleaning)
Try a new coil.
Check the 510 pin and see if you can adjust it (mods/tanks)
Try another tank on your mod.
Try another mod with your tank.
Adjust base of coil carefully if you can (mainly sub-Ohm coils)

How do you fix a short circuit on a vape?

Use these simple tips to troubleshoot the most common vape mod error messages….Check Atomizer

Remove the tank from your mod. Has e-liquid leaked into the mod’s threading?
Disassemble the tank, removing the atomizer coil and then screwing it back in tightly. Reassemble the tank.
Replace the atomizer coil.

How do you know when a coil is bad on a vape?

Signs it’s time to change your vape coil

A burning taste. Vaping a dead coil will eventually result in an acrid, burning taste.
Gurgling sounds. Vapes shouldn’t gurgle.
Weak or “off” e-Juice flavor. This often precedes a burnt taste.
Low vapor production. The vapor produced by your coil will gradually lessen with time.

Why is my vape not working?

Inspect the battery contact; it may be clogged or coated. If this occurs, wipe the contact portion with a Q-tip soaked in rubbing alcohol, let the terminal dry, reconnect your cartridge to the battery and try it again. Do NOT overtighten your cartridge. Make sure your battery is turned on and fully charged.

How do I know if my vape is broken?

5 Signs That Show It’s Time To Change Your Vape Coil

Your Vape Tastes Burnt. This is probably the most noticeable thing that tells you your coil needs replacing, and something most vapers will experience.
Your E-Cigarette Is Gurgling.
Your Vape Tastes ‘Strange’
Your Coil Is Used Up.
E-Cigarette Leaks.

What does it mean when my vape blinks 3 times?

Certain batteries will flash 3 times to indicate a short circuit. Most standard e-cig batteries will have what’s called short circuit protection, so when there is a short and you press the fire button it will just blink 3 times and then won’t do anything. Just check the battery isn’t screwed on too tight.

Why is my vape shorting out?

A short can also happen because of a dirty 510 connector, e-liquid leakage or dust can make its way into the connector, this may cause a weak or dirty connection between the coil and the battery causing problems like a shorted error message. Use a dry cotton bud or tissue to remove dirt or liquid.

How do I change my atomizer?

For Bottom Coil Tanks – Changing Your Coil

Unscrew the mouth piece part (or tank) from the battery (the bottom part).
Make sure that you have some tissue paper on hand.
While your tank is upside down, take off the bottom metal cap.
You simply unscrew this from the tank.
The new coil simply screws into the bottom cap.

Why does my vape mod keep saying Check atomizer?

If your mod is reading the new tank correctly, it could be a problem with the coil on your other tank. You might also want to clean the contact points on the tank that was giving you the error. If your mod is still reading “check atomizer” with a new tank, it’s probably a problem with your mod.

What to do if your atomizer is not working?

To avoid this, cancel and sign in to YouTube on your computer. VapeWild is serious about vaping, and not much else! We like to take a fun spin on things like vape reviews, vape juice tasting, and educational videos! This way, you can enjoy yourself while deciding which products are right for you and learning about your vapes.

How to avoid burnt coils in an atomizer?

How to Avoid Burnt Coils. An error occurred while retrieving sharing information. Please try again later. Check it out now!

Where is the 510 pin on a vape tank?

Fortunately, sometimes it’s an easy fix. If you can unscrew the base of your tank then do so. Inside the bottom section of the tank (usually the airflow control ring) there should be a plate. Push this plate down from the inside so that the 510 pin is sticking out again from the bottom of the tank.