Categories :

What is the default username and password for NETGEAR?

What is the default username and password for NETGEAR?

When you buy a new NETGEAR router, it is configured with factory default settings. When you use the local web address to access your router’s web interface, the user name is admin and the default password is password.

How do I setup my NETGEAR WNDR3400 router?

Setup Step A: Netgear Router Configuration

  1. Remove any cables connecting to the modem. Plug in the modem power adapter and check the power light to ensure the modem is on.
  2. Connect the N600 WNDR3400 router.
  3. Plug in the router power adapter and check the power light to ensure that the router is on.

How do I reset my NETGEAR WNDR3400?

To reset the Netgear WNDR3400 to its default settings, you have to do the following steps:

  1. Put router into operation.
  2. Press Restore Factory Settings button and hold for at least 5 seconds.
  3. Device restarts automatically.
  4. Restoration of standard settings is finished.

How do I set the username and password for my Netgear router?

Launch an Internet browser and type into the address bar.

  1. Enter the router user name and password when prompted.
  2. Click OK.
  3. Select Wireless.
  4. Enter your new network name in the Name (SSID) field.
  5. Enter your new password in the Password (Network Key) fields.
  6. Click the Apply button.

What is Netgear ReadyNAS default password?

What are the factory default settings for my ReadyNAS OS 6 storage system?

Setting Default
Admin user name (case-sensitive) admin
Admin login password (case-sensitive) password
System configuration ReadyNAS local admin page web-based configuration and status monitoring

How do I connect to Netgear Wi-Fi?

Look on the router label for your router’s WiFi network name (SSID) and network key (password). The label is on the back or bottom of your router. On your iOS or Android mobile device, tap Settings > Wi-Fi. Connect your mobile device to the network that is listed on your router’s label and enter the password.

Where is the Reset button on Netgear router?

On Most Netgear Routers. Locate the “Reset” button. It’s on the back of the router and may be labeled “Reset” or “Restore Factory Settings.” The button is small and recessed to avoid accidental resets.

How do I change my router username and password?

To change your router’s password:

  1. Enter your router’s IP address into your favorite web browser.
  2. Log in with the default username and password (both admin, usually).
  3. Go to settings.
  4. Select Change Router Password or a similar option.
  5. Enter the new password.
  6. Save the new settings.

How do I Reset my ReadyNAS admin password?

You can reset your ReadyNAS Admin password by accessing http://ip_address_of_readynas/password_recovery. If you have forgotten the password recovery answer, you will need to perform a firmware re-installation to reset the admin password.

What is the default username and password for Netgear router?

Type your username and password into the security prompt. According to Netgear Support, the default username and password for most Netgear routers is “admin” and “password.”. For older routers, “1234” is the default password. Click “OK” or press “Enter” to log in.

How do I change the wifi password on a Netgear router?

Click on “Wireless Setup. Delete the current password next to the field labeled “Passphrase” under the “Security Options” section. Type in a new password of your choice, then click on “Apply” at the top of the Wireless Setup window. The password for your Netgear Genie router has now been changed.

What is a Netgear router’s default IP address?

Launch your desired web browser

  • Visit or OR Type default gateway address or
  • Login with your username and password
  • How can I Recover my WiFi router password?

    To recover Wi-Fi password of specific Wi-Fi network Right-Click on it and select the “Status” option from the menu. On the Wi-Fi, Status window clicks the “Wireless Properties” button. Select the Security tab on the Wireless Network Properties window.