Close

07/03/2021

How do you remove an inner CV axle?

How do you remove an inner CV axle?

Pry the CV joint. You can use a small pry bar or sturdy flathead screwdriver to pry the axle from the joint. If the axle doesn’t immediately come loose, try twisting it back and force to break the seal. It’s normal for some transmission fluid to leak out as you remove the axle from the cv joint.

How do you remove ATV axles?

2:10Suggested clip 106 secondsATV UTV easy axle removal the proper way – DO IT RIGHT! – YouTubeYouTubeStart of suggested clipEnd of suggested clip

How do you remove a broken RZR 1000 axle?

1:19Suggested clip 54 secondsHow to Remove a Broken axle on a Polaris RZR – YouTubeYouTubeStart of suggested clipEnd of suggested clip

How do you use axle puller?

0:54Suggested clip 47 secondsOEMTOOLS 27032 Flange-Type Axle Puller – YouTubeYouTubeStart of suggested clipEnd of suggested clip

How do you use a master axle puller set?

1:25Suggested clip 39 secondsFairmount 9 Piece Axle Puller Kit – Pull Axle Shafts, Seals – YouTubeYouTubeStart of suggested clipEnd of suggested clip

What is a slide hammer puller?

A slide hammer puller is a tool used to extract these internal car parts by using force, without having to strike or cause damage to any of the vehicle parts.

How do you use a slide hammer to remove a wheel bearing?

0:57Suggested clip 57 secondsHow to Automotive’s Tip on Removing Wheel Bearing Hubs with a …YouTubeStart of suggested clipEnd of suggested clip

How do you use a sliding hammer?

3:55Suggested clip 118 secondsHub Removal with Slide Hammer, Pull a Hub Without a Press …YouTubeStart of suggested clipEnd of suggested clip

What does a slide hammer look like?

Slide hammers typically consist of a long metal shaft with an attachment point at one end, a heavy weight that can slide along the shaft, and a stop for the weight to impact on the end opposite the attachment point. Slide hammers can be attached to objects in multiple ways including screw threads, hooks, and others.

How does a slide hammer bearing puller work?

A Slide Hammer Bearing Puller is a tool designed to pull bearings or other objects that require an internal pulling device to remove it from wherever it may be lodged. When using this device, force is applied to the slide hammer in a back and forth movement, along with the shaft of the sliding rod.

How do you use a slide hammer and bearing puller set?

2:30Suggested clip 103 secondsHarbor Freight Blind Hole Bearing Puller Set 95987 – YouTubeYouTubeStart of suggested clipEnd of suggested clip

How do I remove a blind bearing without a puller?

2:09Suggested clip 109 secondsPulling out a blind bearing without special tools – YouTubeYouTubeStart of suggested clipEnd of suggested clip

How do you remove a wheel bearing without a slide hammer?

Tire and wheel, piece of chain, a bolt and nut, a couple of big washers and a piece of steel with a hole can make an improvised wheel bearing puller.

How do you remove a stuck axle bearing?

2:31Suggested clip 110 secondsStuck Bearing, Broken Axle Bearing, 1997 Jeep Grand Cherokee …YouTubeStart of suggested clipEnd of suggested clip

Can I change a wheel bearing myself?

Changing your own wheel bearings is considered an intermediate job that can be done at home, but will need some speciality mechanic tools. Be sure to obtain your vehicle’s service manual and identify the type of wheel bearing your vehicle is equipped with before you begin the repair.

Can you change a wheel bearing without a press?

2 Answers. I’ve replaced bearings without either a puller or a press, it’s perfectly doable, although a bearing insertion set does make things much easier. These are cheap and you can get them off the internet.